A new addition to the Endeavour Tools range of transmission filling tools. This specialised adaptor is designed for newer gearboxes that have a plastic fill plug.

• Applications: Audi A4 (15-20) | A5 (16-20) | A6 (10-20) | A7 (10-20) | Q5 (08-20)
• 7 speed dual clutch gearboxes
• OEM Equiv: VAS 6617/12

A specialised cylinder head rebuilt kit designed to allow the camshafts to be correctly fitted into the cylinder head on Porsche / VAG common rail engines.

The set contains a jig, various camshaft support fixtures, gear tooth alignment clamps and locking devices.

• OEM Equiv: T40094 | T40095 | T40096
• Applications: VAG 1.6L | 2.0L | 2.7L | 3.0L | 4.0L | 4.2L diesel CR engines | Porsche 3.0 TDi
• For timing servicing on 2.7L - 4.2L engines, also refer ET1622.

Locks chain tensioner in position on VAG petrol engines with a cam belt driving one camshaft & then transferring drive by chain to the other camshaft. A must during assembly & disassembly on 4 | 6 | 8 cylinder engines.

• Applicable years: 98 - 06
• OEM Equiv: 3366 | T20018

Oil pump locking tool for 2.0L, 2.2L, 2.4L, 3.2L diesel engines and 2.3L Duratec petrol engines.

Allows the oil pump to be removed / replaced in the same position (to ensure that the oil pump is not operating with excessive side loads).

• Mondeo | Ranger | Transit (2.0 / 2.2 / 2.4 / 3.2 TDCi / TDDi / Di Duratorq)
• OEM Equiv: 303-705 | 303-1093 (PSA 0198H)

This timing tool kit is designed for 2.0L | 2.4L Ford Duratorq engines (including timing pump removal / installation). Suits engines built from 2002 - 2010.

The kit includes a chain tensioner, fuel pump cover removal tool, fuel pump sprocket locking tool, and camshaft / crankshaft sprocket alignment pins.

• Applications: Ford Transit VH VJ VM | Jaguar X-Type X400
• Engine codes: BG | D2FA | FXFA | H9FA | H9FB
• OEM Equiv: 303-249 | 303-675 | 303-679A | 303-682 | 303-698 | 303-1151

Comprehensive kit for engine timing / timing belt renewal on Holden 1.6D / 1.7D (before 2001) & Isuzu 1.5 / 1.7 / 2.0 / 2.2 / 2.3 / 2.4 / 2.5 / 3.0 / 3.1 engines.

An updated comprehensive timing kit for late model belt driven petrol VAG engines. This kit includes an updated camshaft locking tool for post 2013 engines with Cylinder On Demand (COD).

For the camshaft holding kit refer ET1872A.

• Engines: 1.0L 3 Cyl | 1.2L TFSI | 1.4L TFSI / TSI

Timing chain tension lever designed to be used with the ET0900. Broad range of applications on 1.8L | 2.0L TSFI engines.

For pretensioning the timing chain and unlocking the chain tensioner. Attach to the cylinder head, and then push back the chain tensioning rail. Allows for replacement of timing chain without needing to remove the front cover.

• EA888 Gen III engines (but can also be used with Gen 1 & II)
• Engine codes: 1.8L | CDAA, CDHB, CJEB, 2.0L | CCZA | CCZB | CCZD | CDNB | CESA | CPSA
• OEM Equiv: T40243
• Designed to be used in conjunction with timing kit ET0900

Locking kit for a wide range of VAG 1.8L | 2.0L TFi / TFSi chain drive engines. Plus camshaft adjuster valve tools & crankshaft pulley holding tool.

• OEM Equiv: T10355 | T10368 | T10352 | T10352/1 | T20208 | T40011 | T40267

A specialised kit designed to lock the camshafts and crankshaft in position when servicing VAG EA888 4 cylinder 1.8L | 2.0L 16V petrol engines (2010-).

• Engines: 1.8L: BYT | CDAA | CDHB | CJEB 2.0L: CABB | CAWA | CAWB | CCZA | CCZB | CCZC | CCZD | CDNB | CDNC | CDND | CESA | CPSA

This tool is used for removing the valve springs on VAG group 4 Cyl 1.8L Turbo 20V petrol engines.

• Applications: Audi A4 (B5) | VW Passat (B5)
• OEM Equiv: 3362

A specialised kit for removing the camshaft sprocket from the taper on the camshaft on Pumpe Duse / common rail diesels. Includes a counter hold tool for loosening / tightening the camshaft hub bolt.

• Engines: 1.9L | 2.0L TDI
• OEM Equiv: T10051 | T10052

Adjustable design allows it to work on any sprockets of suitable size. Maximum spoke width - odd numbers 27mm, even numbers 17mm. Forcing screw with 17mm hex head. Body width: 133mm.

• Suits 5 or 6 spoke camshaft pulleys
• OEM Equiv: T40001

For changing V ribbed belts. Use with 1/2" sq drv ratchet or breaker bar.

• Engine codes: ABA | AHL | AHU
• Applications: VW Golf | Passat | Polo (93-99)
• 15mm wide slot.

This puller is designed for the removal of balance shafts fitted to 1.8L | 2.0L chain driven 4 cylinder petrol engines.

• M8 x 1.25 internal thread

For servicing the camshaft adjuster securing bolt on 2.0L TFSi engines. M10 Polydrive (short version) - longer version T10070.

Do NOT use a standard Torx socket when removing the bolt on the camshaft sprocket.

• M10 Polydrive (6 splines)
• 54mm length
• OEM Equiv: T40080
• 1/2" Sq Drv

A set of three assembly camshaft tools for removing camshaft control valves before chain removal, on 4 Cyl chain drive petrol engines.

• Application: 1.8L | 2.0L 4 Cyl chain drive petrol engines
• OEM Equiv: T10352 | T10352/1 | T10352/2
• 3/8" Sq Drv

This locking strap suits VAG 2.4L | 2.8L | 2.7L Turbo 4 Cam 30V engines (99 - 05). Size: 685mm O/A x 6mm & 8mm pins each side x 54mm distance x 40mm hole dia. USE with ET1105-4, ET1657, ET1205B & ET1297.

• Engine codes: ACK | AGA | APR | BBG
• OEM Equiv: 3391

A specialised kit for removing / installing the camshafts on VAG petrol engines. Please refer to ET0900 for the relevant timing tool kit.

• Engines: 1.8L | 2.0L TFSI Turbocharged 4V
• OEM Equiv: T40191 | T40196

Rotate and hold the camshaft on 1.8L | 2.0L TFSI Gen III petrol engines. Use with ET0281 timing kit, and ET9716 crankshaft pulley holding tool.

• Engine: 4 Cyl 1.8L | 2.0L 4V TFSI (Gen III)
• 3/8" Sq Drv
• OEM Equiv: T40266

A specialised wrench to hold the pulley while loosening / tightening the pulley fixing bolt. This tool is recommended by the manufacturer to set the No. 1 cylinder at TDC. Covers engines from 2006 onwards.

• Applications: 1.8L | 2.0L TFSi / TSi petrol engines
• OEM Equiv: T10355

For locking crankshaft at TDC position during timing belt / flywheel / drive plate replacement or removal of the crankshaft bolt.

• Size: M12 x 1.5mm
• OEM Equiv: T40026
• Engine code: ASN | BBJ

This useful kit is designed for locking the fuel pump into its timed position so that the pump drive belt can be replaced or the pump timing checked.

This kit is designed for 2.7L | 3.0L TDi engines.

• Applications: Audi A4 (07-12), A5 (07-12), A6 (08-11) | Q5 (08-12), Q7 (07-12), VW: Phaeton (07-15), Touareg (07-11) | Porsche: Cayenne (08-16)
• Engine codes: 2.7L CAMA, CGKA, CANA, 3.0L: CCWA, CDYA, CASA, CASD
• OEM Equiv: T40135 | 3242 | T10320 | T40058

A specialised tool to remove the toothed belt drive sprocket on high pressure fuel pumps fitted to VAG 3.0L 6 Cyl 4V diesel engines.

• Applications: Audi A5 | A6 | A8 | Q7, VW Phaeton | Touareg
• OEM Equiv: T10320

Designed for V6 4v common rail diesel, chain driven engines. Used for turning over & positioning the crankshaft during removal & installation of the camshaft timing chain. Also contains crankshaft aligning pins (with flats) & side alignment pins for crankshaft to cylinder head.

• Applications: Audi: A4 | A5 | A6 | A8 | Q7 | Allroad, VW: Phaeton | Touareg, Porsche Cayenne

A specialised wrench for counter holding the crankshaft pulley when loosening / tightening the centre bolt on selected VAG engines. This wrench has an angled shaft to assist access on transverse mounted engines.

• Engines: 1.0L | 1.2L | 1.4L 4V injection, toothed belt drive
• 750mm long fixed handle
• OEM Equiv: T10475

A very handy kit, with a wide range of interchangeable pins, for holding the camshaft gear when loosening / tightening the centre bolt.

The adjustable jaw opening / interchangeable pin sets allows this tool to be used almost universally, although with the addition of the T10554 counterhold tool, this kit is specifically designed for VAG vehicles.

• Adaptor sizes: ¯4.8mm, ¯6mm, square 15mm x 6mm, square 15mm x 12mm, cup 13mm x 17mm, cup 16mm x 20mm, Spline M10, M12
• OEM Equiv: T10172 | T10554

A set ot two cam belt tensioner tools for Volkswagen 4 Cyl TDI PD SOHC diesel engines. Also certain Audi / Skoda applications. These tension tools are designed for Pumpe Duse and Common Rail diesels fitted with larger engine mounting brackets.

• OEM Equiv: T10264 | T10265

For TDi PD engines fitted with round crankshaft pulleys. For engines fitted with the oval style pulley refer ET2207.

• Applications: Chrysler Sebring, Dodge Avenger | Caliber, Jeep Compass | Patriot
• Engine codes: ECD

A specialised kit for engine timing / timing belt replacement on VAG 1.4 - 2.0D Pumpe Duse, and 1.4L | 1.6L | 2.0L CR diesels.

These tools are also suitable for similar engines fitted to Ford | Dodge | Chrysler vehicles.

• Use in conjunction with ET1657.

A popular timing tool kit for a wide range of common Audi / Skoda / VW vehicles including many 1.4 | 1.9 | 2.0 TDi PD DOHC engines.

• Includes two versions of the camshaft sprocket locking tool.
• For belt driven diesel engines.

This kit provides the essential camshaft | crankshaft | tensioner tools for working on popular VAG vehicles with 1.4L FSI and 1.6L | 1.9L | 2.0 TDi PD engines fitted to MK5 - MK6 generation vehicles fitted with toothed timing belts.

This kit is suitable for use with cam belt kits including INA 531020110, Contitech CT1028K3, Gates K055569XS.

• OEM Equiv: 310-084 (T10008) | 310-085 (T10050) | T20102 | 310-1054 (T10115) | T10060 | T10100 | T10020 | T10264 | T10265

Specialised locking tool kit for 5th generation diesel Blue Motion engines. Set includes crankshaft locking tools for both styles of VAG sprockets.

• For Gen 5 common rail diesels (Blue Motion)
• Applications include 1.6L | 2.0L TDi engines fitted to Audi A3 | A4 | A5 | A6 | Q5, VW Golf | Passat | Tiguan
• OEM equiv: T20102 (3359) | T10050 |T10051 | T10052 | T10100 | T10255 | T10264 | T10265 | T40098

These two tools are required for setting the camshaft / tensioner on 1.6L | 2.0L petrol engines found in various VAG vehicles from 1997 - 2011.

This kit is suitable for use with replacement cam belt kit: Contitech CT908K1, Gates K015489XS, INA 530 0171 10.

A specialised timing tool kit is for 1.8L | 2.0L TSi / TFSi 4v engines. This kit includes a TDC indicator. The TDC indicator needs to be used in conjunction with a DTI gauge. The DTI gauge (ET1101) is not included in the kit, but is available separately.

This kit is designed to allow removal / replacement of the timing chain and camshaft sprockets. The kit includes special camshaft pulley locking blocks for late model Gen 3 TSi / TFSi engines.

On third-generation EA888 1.8 and 2.0L 4V TFSI engines, the ET0037A is required to remove the damper pulley when servicing the timing chain.