Power Probe

A 20 foot extension cable for Power Probe 3 circuit testers. Great for working on trucks, trailers and oversized vehicles.

• Original part # PN3049

20 foot extension cable for the Power Probe 4 / Maestro.

This clip set allows your Power Probe circuit tester to be powered from any 12V source. Suits all Power Probe 3 models only.

• Original part # PN3046

The original Power Probe 3 uses a 20ft cable which attaches to the vehicle's battery, allowing the user to perform an electrical test anywhere in, or around the vehicle. The PP3 is a Voltmeter and Continuity Tester, with Audible & Visual indicators along with two LED headlights to light up your work area. This circuit tester also supplies Battery Voltage or Ground to activate components. This powerful time-saver tool is perfect for every level of technician.

• Voltmeter and Continuity Tester
• Relay & component tester
• Supply battery voltage and ground to test components
• Audio tone 20' Jumper lead
• Works on 12-24V sources
• Protected by 8 Amp circuit breaker

Perform battery checks, charging system checks, fuse checks, voltage checks, component tests...

All at the flick of the switch, while being guided through with our two NEW menu options: EZLEARNING and EZDIAGNOSTIC.

• New larger LCD screen
• Upside down? No problem! New flip screen feature
• Menu driven. Makes navigating a breeze
• Limited edition carbon fibre skin

Perform battery checks, charging system checks, fuse checks, voltage checks, component tests...

All at the flick of the switch, while being guided through with our two NEW menu options: EZLEARNING and EZDIAGNOSTIC.

• New larger LCD screen
• Upside down? No problem! New flip screen feature
• Menu driven. Makes navigating a breeze

The Power Probe 4 is a multi-use Circuit Tester with built-in diagnostic power.

This tool simplifies the testing of fuse boxes, verifies correct operation of motors, lights, relays, sensors, wires, communications circuits and computer drivers. The large LCD colour display makes viewing live test information and mode selection simplified in even direct sunlight or complete darkness.

• Supplies Power and Ground
• Digital voltmeter with Min/Max voltage capturing
• 20 ft power lead
• Tests for bad grounds / short circuits
• Powered by vehicle battery
• Gold plated brass probe tip
• Directed LED head lamps to illuminate test area
• Ohmeter / Frequency
• Pulse width (+tive & -tive)

Additional diagnostic modes:

• Petrol fuel injection tester
• PCM / ECM driver tester
• Signal tracer (use with ECT3000)

The Power Probe 4 Master Combo Kit combines the Power Probe 4, ECT3000 and various accessories to provide the ultimate combination of diagnostic and circuit-testing capabilities.

The Power Probe 4 provides simplified testing of Motors, Lights, Relays, and Sensors, and even Fuel Injectors. Also, like all Power Probe circuit-testers, it supplies Power and Ground for functional component testing on or off the vehicle. The ECT3000 will help you trace short and open circuits quickly and accurately.

Connects to any Power Probe. Limits output voltage to 5V. Essential for safely testing sensors and computer circuits on vehicles. Now you can supply a 5V reference signal to test computer modules, wiring and the components connected to them.

This leadset contains an adaptor cap and banana jack.

• For Power Probe I & II only

This Power Probe kit contains two adaptors - a male / male and a female / female adaptor.  The 4mm connectors are suitable to use with all standard multimeters.

• male / male adaptor
• female / female adaptor

Banana jack alligator clip. This clips suits all Power Probe circuit testers.

• Original part # PN024

This set comprises a universal 4mm wire and alligator clip connector.

• Original part # PNECT057

Apply voltage from the Power Probe tip to quickly actuate components.

• Test circuits for voltage, continuity or polarity. Green / red LEDs provide quick confirmation.
• 6m heavy duty extension lead.

Replacement battery clip for the Power Probe 4.

• Original part # PP401

This Power Probe adaptor kit contain two adaptors, one with a blade probe for tapping into fuse sockets, and the second, a needle probe for back probing connectors.

• Allows for pinpoint diagnostic testing
• 4mm banana plugs
• Suits all Power Probe circuit testers
• Old part numbers: AA4 | AA6

Replacement self resetting circuit breaker for the Power Probe 4.

• Original part # PC8A

The ECT3000 Electrical Short and Open Finder makes locating shorts and opens quickly and more accurately than ever before. When the ECT3000 Transmitter is connected to an isolated circuit, it will quickly determine if the circuit has an open or if the circuit is shorted to ground. The ECT3000 receiver is designed to detect signals from the transmitter and its new adjustable distance indicator allows for accurate detection.

• Transmitter quickly determines if circuit has an open or if circuit is shorted to the ground.
• Receiver features a new adjustable distance indicator.
• Light bulb sockets for testing lighting systems. Plus probes / alligator clips.
• Works on 12-24V systems.

Measures up to 20A (and as low as 1 milliamp). Displays current in realtime. Adaptors work with all Power Probe circuit testers!

The Power Probe Digital Clamp Meter is an 80 Amp, auto-ranging clamp meter designed specifically for the automotive technician. This meter is rated CAT III 600V and can measure Volts, Amps, Ohms, Frequency and Temperature, necessary for automotive electrical testing. This meter's diagnostic applications include (but are not limited to) Parasitic Draw, Crank Current testing and HVAC Temperature testing.

Supplied with 3x AAA batteries.

• Voltage: AC 600V | DC 600V
• Current: AC 80A | DC 80A
• Display 4000 counts
• Jaw Opening 24mm/0.9"
• Auto & Manual Ranging
• Auto Power Off / Non-Contact Voltage Detector
• Diode Open Voltage 3.2V
• Continuity Buzzer <50
• Data Hold
• Large LCD Display Backlight
• Work Light
• Low Battery Display

Replacement fuse holder for the Power Probe 4.

The Gold Series Lead Set gives you the ability to extend your Power Probe circuit tester.

This kit includes 3 extension leads, 2 adaptors, two piercing probes and an extra probe tip. A must have kit for diagnosing electrical issues.

• Super flexible 10 gauge leads - stackable (1ft | 3ft | 6ft)
• Power Probe replacement tip
• Small piercing probe (Green) - for 20-28 gauge wires
• Large piercing probe (Yellow) - for 8-18 gauge wires
• 4mm female - female adaptor
• 4mm male - male adaptor
• Alligator clip adaptor
• Adaptor cap

The original! A powerful time saver perfect for all technicians.

• Voltmeter & Continuity tester
• Relay & component tester
• Supply battery voltage & ground to test components
• Works on 12-24V sources
• Audio tone
• 20’ Jumper lead

Power Probe cigaratte adaptor for use with Power Probe 3 | 3S | 3EZ. Designed to allow Power Probe to be powered through the vehicle's cigarette port.

• Original part # PN3048

Check out Power Probe's newest tool - The Maestro - with all the features of the PP4 PLUS the built-in diagnostic power to display waveforms.

The Maestro wirelessly pairs with our Power Probe App, allowing for a wireless remote display as well as data streaming and recording.

Files can be emailed, exported or simply saved for future reference.

Easily verify correct operation of:

• Motors
• Lights
• Relays
• Sensors
• Wires

Easy to use plug-in style current testers.
A simple way to test any USB (especially on car accessory outlets).

Multimeter extension leads suitable for use with PowerProbe multimeters, and any multimeter using standard 4mm plugs.

• 10 foot red test lead
• 10 foot black test lead
• Old part # PNLS025-36RED | PNLS025-36BLK

The Power Probe OBD-II Breakout Box is a CAN Bus circuit tester compatible with 12 and 24 Volt systems. The tool connects directly into the Vehicle's Data Link Connector (DLC) testing for any abnormalities such as shorting and reverse polarity at the pins. If shorting or reverse polarity is present, connecting the PPECB first will prevent harm before connecting a Diagnostic Scan Tool. The Breakout Box provides a live display of present communicating signals without having to use a Digital Multimeter. Additionally, you can quickly test the voltages at all 16 pins.

• Test DLC (OBD port) for any abnormalities, such as shorting and reverse polarity at the pins before connecting other diagnostic equipment to DLC.
• Provides a live display of communicating signals (eg. communication protocol signals) on assigned pins for quick pointing of faults without having to bring out a measurement tool (digital volt ohmmeter)
• Quickly access all 16 pin connections during repair and diagnosis of the vehicle
• Monitor the input voltage of the OBD during module programming with the low voltage alarm
• 2 pin adapter included

The Power Probe Penetrator provides extra durability, with a 3.5mm Tungsten tip. Easily penetrate rust etc.

• Compatible with all current Power Probes with removeable tip
• Standard 4mm banana jack
• Provides highly stabilised readings

The PPPWM is an adapter that is plugged into Power Probe products with 4mm banana plugs (such as THE MAESTRO / PP4 / PP3 / PP3EZ etc).

The adapter can be set for the output 0-100% pulse width drive waveform by pressing the key. It is mainly used for automotive applications such as automotive fan circuit detection, to find the part of the circuit failure, in order to replace and repair.

Duty cycle adjustable 5% - 100%.

For 12V / 24V use. 10A max continuous output.

• Old part # PN005
• 2 pack

Replacement 3" probe tips, suitable for all Power Probe units. These are the original tips supplied with all Power Probe units. For a longer 6" tip, please refer to PPTK0043.

• With 4mm banana jack
• Original part # PN3015-BLK
• 2 pack

Our new longer 6" tip for getting into those hard to reach areas.

• With 4mm banana jack
• Sold individually
• See PPTK0024 for original 3" size in a twin pack

The DM500MAX is designed for harsh environments with a watertight gasket as the seams rotary switch, an input terminal, and battery cover to keep out dust, dirt, and splashing. It can also take shocks and drops, work anywhere from indoor to outdoor, and special designed LoZ(Low Impedance) feature to prevent false reading caused by ghost voltages.

• 40,000 count extra-large digital display
• Auto backlit / dual display
• Auto AC / DC voltage detection with low impedance
• Auto save mode to automatically save new readings
• 40,000 records data logging capacity

A 3 foot wire extension for use with all Power Probe testers, plus most other diagnostic equipment which uses a standard 4mm banana plug.

• 3 foot wire extension
• 10 gauge multi strand wire
• 4mm banana plug connectors
• Stackable for versatility
• Original part # PNLS025-36RED