Packaged in a BMC, this circuit tester has a standard 4mm connector which can be used with standard multimeter probes.

Wire piercer / probes / alligator clip included.

• Not for use with airbags / vehicle computers.
• For use with DC voltage only.

Connects to any Power Probe. Limits output voltage to 5V. Essential for safely testing sensors and computer circuits on vehicles. Now you can supply a 5V reference signal to test computer modules, wiring and the components connected to them.

The ECT3000 Electrical Short and Open Finder makes locating shorts and opens quickly and more accurately than ever before. When the ECT3000 Transmitter is connected to an isolated circuit, it will quickly determine if the circuit has an open or if the circuit is shorted to ground. The ECT3000 receiver is designed to detect signals from the transmitter and its new adjustable distance indicator allows for accurate detection.

• Transmitter quickly determines if circuit has an open or if circuit is shorted to the ground.
• Receiver features a new adjustable distance indicator.
• Light bulb sockets for testing lighting systems. Plus probes / alligator clips.
• Works on 12-24V systems.

This true RMS clamp meter provides accurate AC, AC/DC Current and Voltage readings regardless of waveforms. This meter can be used in most industrial and commercial applications where non-linear loads distort the Current or Voltage waveform.

• 30mm clamp opening
• 1000A current AC / DC
• 600V voltage AC / DC
• 4000 Digital display counts
• CAT III 600V rating

The original! A powerful time saver perfect for all technicians.

• Voltmeter & Continuity tester
• Relay & component tester
• Supply battery voltage & ground to test components
• Works on 12-24V sources
• Audio tone
• 20’ Jumper lead

Perform battery checks, charging system checks, fuse checks, voltage checks, component tests...

All at the flick of the switch, while being guided through with our two NEW menu options: EZLEARNING and EZDIAGNOSTIC.

• New larger LCD screen
• Upside down? No problem! New flip screen feature
• Menu driven. Makes navigating a breeze
• Limited edition carbon fibre skin

Test battery charge / health for all 12V auto batteries and alternator / crank systems for 12V / 24V batteries, including new stop start batteries.

Print test results using the built in printer.

• Tests all main battery standards
• Max load voltage tests for 12V / 24V
• Short circuit / reverse polarity protection

This pressure brake bleeder is designed to be portable, being powered by the vehicle's 12V battery. No shop air required!

Features adjustable output pressure up to a maximum 3.0 bar, with automatic cut-off function when pressure falls below 0.5 bar.

Supplied with premium quality adaptor set made from metal, not plastic.

• Suitable for both hydraulic brake and clutch systems.

This petrol engine timing light is designed for professional use. Featuring multiple measurement modes and a rotating barrel for better aim at the timing market and LCD viewing angle.

• Tachometer: 249 to 9,990 RPM (± 1% Accuracy)
• Dwell: 0¡ to 180¡ / 2 - 12 cylinders (±1% Accuracy)
• Voltage: 10 - 16V DC (± 1% Accuracy)
• Advance Degrees (2 / 4 cycle DIS & Conventional): 0¡ to 90¡ ( ± 0.5¡ Accuracy)

This true RMS clamp meter provides accurate AC, AC/DC Current and Voltage readings regardless of waveforms. This meter can be used in most industrial and commercial applications where non-linear loads distort the Current or Voltage waveform.

• 30mm clamp opening
• 1000A current AC / DC
• 600V voltage AC / DC
• 4000 Digital display counts
• CAT III 600V rating

This advanced system tester is designed to test all 12V auto batteries (lead, AGM, EFB, GEL etc) including stop / start batteries. The unit tests battery condition PLUS charging (alternator) and starter (crank) systems.

The battery test analyses battery health status to calculate actual cold cranking capability of the battery. The tester will advise whether the battery needs replacing, and is also able to identify a faulty battery before actual failure.

The cranking test analyses the starting circuit (including the starter motor) by measuring increases in starting torque load. The charging test analyses the charging system, detecting under or overcharging.

• Testing range: 100 - 2,000CCA
• Powered from vehicle's 12V battery | no internal battery required

A professional quality kit for removing aftermarket wheel lock nuts. This kit includes a wide range of sockets / bits for removing locking wheel nuts.

• See download link for detailed socket listing
• Made from Chrome Vanadium steel for added durability