Effective diagnostic tool for determining whether faults are due to the turbo system, or simple air leaks.

• Includes 3 pairs of stepped adaptors to fit most sizes found on commercial vehicles.
• Includes pressure gauge, shut off valve, and pressure release valve.
• Adaptor sizes: 105 - 130mm

This gauge tests belt tension, for the precise adjustment of engine drive belts. Universal application including timing belts, fan belts, grooved / ribbed / toothed v-belts. Convenient T handle design.

Simply place the belt between the roller pins and the pressing handle. Turn the T handle clockwise (until the t-bar is tight). Check displacement (5-10mm). Refer to vehicle manual for recommended displacement.

These reels hold 6 metres of highly flexible double skinned silicone cable suitable for use with standard multimeters.

• 1000V CATIII double / reinforced insulation | 20 Amp current rating
• 4mm Straight plug / 4mm Right angle plug
• Fully compliant to IEC 61010-031:2015

Convert your Android scan tool into a professional battery tester! Or use with your mobile phone / tablet. Easily send test reports by email.

• Works with all common automotive batteries including AGM / GEL / Lithium.
• Professional tester showing battery status, charging / cranking tests, and voltage monitoring for deep analysis.

Advanced detector using ultrasonic waves to detect leaks in a range of automotive / industrial applications. Tone generator to check for faulty seals in non pressurised enclosures.

• Detect vacuum / compressed air leaks (down to .13mm)
• Gas turbulence / with air / gas line blockages
• Electrical discharge due to insulation breakdown
• Mechanical wear in bearings, race assemblies etc
• Detect leaks in door seals, vehicle compartments etc

Highly accurate tester measures material thickness, including steel. For automotive, great for measuring piston head thickness.

• 90 cm cable
• 5 mHz probe frequency
• 0.8 - 500 mm range (steel)
• Up to 0.01 mm resolution (1-99 mm)
• Accuracy: H<10 mm, /- 0.05 mm | 10-99 mm /- (0.01 H/200) mm
• Next gen higher resolution

Test battery charge / health for all 12V auto batteries and alternator / crank systems for 12V / 24V batteries, including new stop start batteries.

Print test results using the built in printer.

• Tests all main battery standards
• Max load voltage tests for 12V / 24V
• Short circuit / reverse polarity protection

A professional quality automotive battery tester for testing both 12V lithium ion and lead acid batteries. This tester uses conductance technology; a passive testing methodology which does not discharge / drain the battery. This analyser also checks the alternator's charging and starter's cranking condition.

• Tests all 12V lithium ion / lead acid batteries for cars / motor cycles.
• Print function via PC printer
• Testing range: Lithium ion 20- 1000CCA | Lead acid 20 - 2000CCA

This petrol engine timing light is designed for professional use. Featuring multiple measurement modes and a rotating barrel for better aim at the timing market and LCD viewing angle.

• Tachometer: 249 to 9,990 RPM (± 1% Accuracy)
• Dwell: 0¡ to 180¡ / 2 - 12 cylinders (±1% Accuracy)
• Voltage: 10 - 16V DC (± 1% Accuracy)
• Advance Degrees (2 / 4 cycle DIS & Conventional): 0¡ to 90¡ ( ± 0.5¡ Accuracy)

A professional quality tester designed for late model vehicles fitted with 13 pin Euro type sockets fitted to the back of the vehicle.

This tester is designed for testing the vehicle side socket, not the trailer itself.

• Tests socket functionality on modern 13 pin Euro sockets. Can also test legacy 7 pin sockets (separate adaptor).
• CANbus compatible to also test 12V continuous / ignition live feeds and the reversing lights. Useful when diagnosing faults.
• Built in self test function on the tool.
• Supplied with 4m cable to allow the unit to be used while sitting in the vehicle.
• Powered by vehicle 12V power supply.

This true RMS clamp meter provides accurate AC, AC/DC Current and Voltage readings regardless of waveforms. This meter can be used in most industrial and commercial applications where non-linear loads distort the Current or Voltage waveform.

• 30mm clamp opening
• 1000A current AC / DC
• 600V voltage AC / DC
• 4000 Digital display counts
• CAT III 600V rating

This advanced system tester is designed to test all 12V auto batteries (lead, AGM, EFB, GEL etc) including stop / start batteries. The unit tests battery condition PLUS charging (alternator) and starter (crank) systems.

The battery test analyses battery health status to calculate actual cold cranking capability of the battery. The tester will advise whether the battery needs replacing, and is also able to identify a faulty battery before actual failure.

The cranking test analyses the starting circuit (including the starter motor) by measuring increases in starting torque load. The charging test analyses the charging system, detecting under or overcharging.

• Testing range: 100 - 2,000CCA
• Powered from vehicle's 12V battery | no internal battery required