This digital tachometer provides fast and accurate - contact and non contact - RPM and surface speed measurement of rotating objects.

This tachometer features a wide measurement range (from a very low RPM) and high resolution.

• Range: 2~99,999 rpm (non-contact)
• Range: 2~20,000 rpm (contact)
• Detecting distance: 50mm - 500mm
• Accuracy: +/- 0.05% 1 digits
• Min / Max & calibration function
• Auto Power Off
• 5 digit LCD display
• 9V battery included

A new safety blow gun from Air Boy featuring high airflow | Low noise level | Unblockable tip | Integrated chip shield.

• 600l / min @ 8 bar
• 78 db @ 6 bar
• OSHA STD 1-13.1 compliant
• Industry leading airflow for a low noise blow gun

Many late model vehicles require that the ride height be checked / set correctly to ensure that ADAS systems function correctly. Our tool measures ride height either under the sills, or under vehicle centre (without needing to crawl under the vehicle).

• Measures from 51 - 350mm
• Magnetic tape measure to allow ride height to be adjusted, while making measurements
• Ensure vehicle is on level ground before taking any measurements

Test battery charge / health for all 12V auto batteries and alternator / crank systems for 12V / 24V batteries, including new stop start batteries.

Print test results using the built in printer.

• Tests all main battery standards
• Max load voltage tests for 12V / 24V
• Short circuit / reverse polarity protection

A professional quality automotive battery tester for testing both 12V lithium ion and lead acid batteries. This tester uses conductance technology; a passive testing methodology which does not discharge / drain the battery. This analyser also checks the alternator's charging and starter's cranking condition.

• Tests all 12V lithium ion / lead acid batteries for cars / motor cycles.
• Print function via PC printer
• Testing range: Lithium ion 20- 1000CCA | Lead acid 20 - 2000CCA

This petrol engine timing light is designed for professional use. Featuring multiple measurement modes and a rotating barrel for better aim at the timing market and LCD viewing angle.

• Tachometer: 249 to 9,990 RPM (± 1% Accuracy)
• Dwell: 0¡ to 180¡ / 2 - 12 cylinders (±1% Accuracy)
• Voltage: 10 - 16V DC (± 1% Accuracy)
• Advance Degrees (2 / 4 cycle DIS & Conventional): 0¡ to 90¡ ( ± 0.5¡ Accuracy)

A professional quality tester designed for late model vehicles fitted with 13 pin Euro type sockets fitted to the back of the vehicle.

This tester is designed for testing the vehicle side socket, not the trailer itself.

• Tests socket functionality on modern 13 pin Euro sockets. Can also test legacy 7 pin sockets (separate adaptor).
• CANbus compatible to also test 12V continuous / ignition live feeds and the reversing lights. Useful when diagnosing faults.
• Built in self test function on the tool.
• Supplied with 4m cable to allow the unit to be used while sitting in the vehicle.
• Powered by vehicle 12V power supply.

This true RMS clamp meter provides accurate AC, AC/DC Current and Voltage readings regardless of waveforms. This meter can be used in most industrial and commercial applications where non-linear loads distort the Current or Voltage waveform.

• 30mm clamp opening
• 1000A current AC / DC
• 600V voltage AC / DC
• 4000 Digital display counts
• CAT III 600V rating

This advanced system tester is designed to test all 12V auto batteries (lead, AGM, EFB, GEL etc) including stop / start batteries. The unit tests battery condition PLUS charging (alternator) and starter (crank) systems.

The battery test analyses battery health status to calculate actual cold cranking capability of the battery. The tester will advise whether the battery needs replacing, and is also able to identify a faulty battery before actual failure.

The cranking test analyses the starting circuit (including the starter motor) by measuring increases in starting torque load. The charging test analyses the charging system, detecting under or overcharging.

• Testing range: 100 - 2,000CCA
• Powered from vehicle's 12V battery | no internal battery required