This kit helps clean / decarbonise the injector hole. Plus the seat cutters clean the bottom of the injector hole to allow proper setting of the new copper washer.

Helps avoid blow back due to poorly seated injectors.

• 3 seat cutters: 17mm flat | 17mm angled | 21mm angled
• Includes washer removal tool, injector blanking plugs (stop debris entering cylinders), wire brush cleaning set for chamber walls and centralising stem for correct cleaning seating angle

• 12 Point
• Deep
• 1/2" Sq Drv
• Sizes: 29, 30, 32, 34, 35, 36, 38, 39mm

These flare type injection wrenches are designed to access hard to reach diesel injectors. They have a long 125mm shank, with flexible heads, providing up to 220 degrees of movement.

These wrenches are made by hot forging, providing a far superior torque capacity to standard injection wrenches.

• Single hex | 3/8" Sq Drv
• Sizes: 12 x 110mm | 14 x 115mm | 16 x 125mm | 17 x 125mm | 18 x 125mm | 19 x 125mm

A must for all workshops. This ATF transmission fluid filler comes with a 15 pce adaptor kit (durable metal construction) giving it near universal coverage.

• 15 pce metal adaptor kit includes VW DSG, VZ Commodore, Falcon
• Large 12.5L tank

Professional quality for cleaning / testing petrol inejctors including new GDI type.

• Suits Low / High resistance PFI, GDI Peak & Hold and GDI Piezo
• Conduct sprayability and leakage tests
• Adjustable test voltage from 12V - 170V. Adj current from 3 - 20A. Maximum power: 150W
• Pulse width: 4,000 - 9,000uS
• Pressure: from 1 - 20 Bar
• 60W ultrasonic cleaner

Test battery charge / health for all 12V auto batteries and alternator / crank systems for 12V / 24V batteries, including new stop start batteries.

Print test results using the built in printer.

• Tests all main battery standards
• Max load voltage tests for 12V / 24V
• Short circuit / reverse polarity protection

This pressure brake bleeder is designed to be portable, being powered by the vehicle's 12V battery. No shop air required!

Features adjustable output pressure up to a maximum 3.0 bar, with automatic cut-off function when pressure falls below 0.5 bar.

Supplied with premium quality adaptor set made from metal, not plastic.

• Suitable for both hydraulic brake and clutch systems.

This petrol engine timing light is designed for professional use. Featuring multiple measurement modes and a rotating barrel for better aim at the timing market and LCD viewing angle.

• Tachometer: 249 to 9,990 RPM (± 1% Accuracy)
• Dwell: 0¡ to 180¡ / 2 - 12 cylinders (±1% Accuracy)
• Voltage: 10 - 16V DC (± 1% Accuracy)
• Advance Degrees (2 / 4 cycle DIS & Conventional): 0¡ to 90¡ ( ± 0.5¡ Accuracy)

This true RMS clamp meter provides accurate AC, AC/DC Current and Voltage readings regardless of waveforms. This meter can be used in most industrial and commercial applications where non-linear loads distort the Current or Voltage waveform.

• 30mm clamp opening
• 1000A current AC / DC
• 600V voltage AC / DC
• 4000 Digital display counts
• CAT III 600V rating

This advanced system tester is designed to test all 12V auto batteries (lead, AGM, EFB, GEL etc) including stop / start batteries. The unit tests battery condition PLUS charging (alternator) and starter (crank) systems.

The battery test analyses battery health status to calculate actual cold cranking capability of the battery. The tester will advise whether the battery needs replacing, and is also able to identify a faulty battery before actual failure.

The cranking test analyses the starting circuit (including the starter motor) by measuring increases in starting torque load. The charging test analyses the charging system, detecting under or overcharging.

• Testing range: 100 - 2,000CCA
• Powered from vehicle's 12V battery | no internal battery required

A professional quality kit for removing aftermarket wheel lock nuts. This kit includes a wide range of sockets / bits for removing locking wheel nuts.

• See download link for detailed socket listing
• Made from Chrome Vanadium steel for added durability